It is a one type of resistor whose resistance varies depending on the amount of light falling on its surface. When the light falls on the resistor, then the resistance changes. These resistors are often used in many circuits where it is required to sense the presence of light. These resistors have a variety of functions and resistance.

Read On

Caddock Current Sense Resistors, Non-Inductive Designs, High Stability, Surface Mount Non-Inductive Designs, Low Resistance, Current Sense Resistors, in Axial, Radial, TO-Style, SMT, Chip and, D-Pack style packages. High Stability, Surface Mountable. Current Sense Resistors Power Film Resistors SMT Resistors Precision High Voltage Resistors

Read On

this series resistor doing to music as the resistor reacts against the input tube's characteristics and reacts as well with input wiring to the tube's grid, and also acts as a severe snubber of incoming dynamic energy/current content and event timing accuracy." No it doesn't. You are full of crap. Tre' Have Fun and Enjoy the Music

Read On

Mills Resistors Mills Resistors The engineers at Mills Resistor Corporation have been designing and producing high quality resistors since 1944. They continue to produce audio-grade wirewound resistors as part of Vishay Intertechnology. Subscribe to …

Read On

Mills Series Non-Inductive wire-wound, axial bodied, power resistors are very popular in audio, infinitely better than the ceramic "grey" type. An Aryton-Perry design with tinned copper leads, silver-plated end caps.

Read On

The resistor colour code was invented in the 1920s by the Radio Manufacturers Association (RMA). All leaded resistors with a power rating up to one watt are marked with colour bands. They are given by several bands and together they specify the resistance value, the tolerance rate and sometimes the reliability or failure rates.

Read On

Walsin offers a complete portfolio of Chip Resistor to fulfill diversified applications from automotive electronics, smartphones, networking devices, and much more. Series of Walsin's Thick Film Chip Resistors is enclosed below for your reference, or simply select a search method preferred from the below.

Read On

High quality audiophile & DIY audio resistors - Mills MRA-12 12 watt. Values from 0.1 ohm to 100K ohm (0R1 - 100K). Non-magnetic, non-inductive.

Read On

Co-Browse. By using the Co-Browse feature, you are agreeing to allow a support representative from Digi-Key to view your browser remotely. When the Co-Browse window opens, give the session ID that is located in the toolbar to the representative.

Read On

Resistors in series and parallel Resistors in series. When resistors are connected in series, the current through each resistor is the same. In other words, the current is the same at all points ...

Read On

The different sets of standard resistor values are known by their E-series numbers: E3 has three resistors in each decade, E6 has six, E12 has twelve, and so forth. The most basic series within the E range is the E3 series which has just three values: 1, 2.2 and 4.7.

Read On

Thick Film Power Low ohm Current Sense Chip Resistor (Automotive) 0402 – 2512, 0.01 – 0.976ohm, ... Tantalum nitride Thin Film Chip Resistor / MF Series . Anti-sulfuraion against ASTM-B-809-95* Modified (Sulfur 1000 hours, 105°C) AEC-Q200 Qualified Size: 0402 ~ 1206 TCR:10ppm ~ 50ppm

Read On

Then series resistor networks can also be thought of as "voltage dividers" and a series resistor circuit having N resistive components will have N-different voltages across it while maintaining a common current.. By using Ohm's Law, either the voltage, current or resistance of any series connected circuit can easily be found and resistor of a series circuit can be interchanged …

Read On

Every resistor has a specific maximum power rating. In order to keep the resistor from heating up too much, it's important to make sure the power across a resistor is kept under it's maximum rating. The power rating of a resistor is measured in watts, and it's usually somewhere between ⅛W (0.125W) and 1W.

Read On

wattage rating of a carbon-film resistor to meet the following requirements. The resistor has a 54-V IR drop when its current is 20 mA. The resistors available have the following wattage ratings: 1/8 W, 1/4 W, 1/2 W, 1 W, and 2 W.

Read On